Arduino on Mageia linux

[Rabin Yasharzadehe]

what is the output of `dmesg` when you connect the device to the machine ?

e.g, should be something like this,

[393503.604738] usb 1-4.2: new full-speed USB device number 71 using
xhci_hcd
[393503.698674] usb 1-4.2: New USB device found, idVendor=1a86,
idProduct=7523
[393503.698678] usb 1-4.2: New USB device strings: Mfr=0, Product=2,
SerialNumber=0
[393503.698681] usb 1-4.2: Product: USB2.0-Serial
[393503.757764] usbcore: registered new interface driver ch341
[393503.757789] usbserial: USB Serial support registered for ch341-uart
[393503.757808] ch341 1-4.2:1.0: ch341-uart converter detected
[393503.758600] usb 1-4.2: ch341-uart converter now attached to ttyUSB0


--
Rabin

On 20 June 2017 at 14:20, Shlomo Solomon <shlomo.solomon at gmail.com> wrote:

> Sorry - just noticed I cut off part of the error message, so here it is
> again:
>
> WARNING:  RXTX Version mismatch
>         Jar version = RXTX-2.2
>         native lib Version = RXTX-2.2pre2
> Binary sketch size: 1,056 bytes (of a 32,256 byte maximum)
> avrdude: stk500_recv(): programmer is not responding
> avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x00
> avrdude: stk500_recv(): programmer is not responding
> avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x00
>
>
>
>
>
> On Tue, 20 Jun 2017 13:32:28 +0300
> Shlomo Solomon <shlomo at the-solomons.net> wrote:
>
> > I installed the Arduino IDE from Mageia RPMs and added my user to the
> > lock group as instructed.
> >
> > In the tools >> serial port menu, there is no  /dev/ttyUSB0 -
> > only /dev/ttyS0 and  /dev/ttyS1. I tried both of them but could not
> > upload a program. I read that sometimes Arduino needs to be run as
> > root, so I tried that too with no success. Here's what I get when I
> > try to upload:
> >
> > Binary sketch size: 1,056 bytes (of a 32,256 byte maximum)
> > Binary sketch size: 1,056 bytes (of a 32,256 byte maximum)
> > avrdude: stk500_recv(): programmer is not responding
> > avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x00
> > avrdude: stk500_recv(): programmer is not responding
> > avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x00
> > avrdude: stk500_recv(): programmer is not responding
> >
> >
> >
>
>
>
> --
> Shlomo Solomon
> http://the-solomons.net
> Sent by Claws Mail 3.11.1 - KDE 4.14.5 - LINUX Mageia 5
>
>
> _______________________________________________
> Linux-il mailing list
> Linux-il at cs.huji.ac.il
> http://mailman.cs.huji.ac.il/mailman/listinfo/linux-il
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://mailman.cs.huji.ac.il/pipermail/linux-il/attachments/20170620/0e9dcb8a/attachment.html>